80 Plus vs Cybenetics: PSU efficiency ratings explained

80 Plus checks PSU efficiency at fixed load points; Cybenetics averages the full range and adds a noise grade. Tier tables and how to read both.

80 Plus and Cybenetics both grade power supply efficiency, but they measure it differently. 80 Plus checks a unit at a few fixed load points and sets a pass mark for each tier. Cybenetics ETA measures efficiency across the whole operating range, averages it, and also grades fan noise separately under LAMBDA. A "Gold" label from one scheme therefore does not equal a "Gold" label from the other.

The short answer

  • 80 Plus: pass/fail at 20%, 50% and 100% of rated load, with a 10% point (and 5% for Ruby) only in the top tiers. It says nothing about noise.
  • Cybenetics ETA: an average over more than 1,450 load combinations, so one weak spot in the curve pulls the grade down.
  • Cybenetics LAMBDA: a separate noise class, from Standard to A++, based on fan noise measured across the load range.

Both programs are voluntary. A missing certificate means the manufacturer did not submit the unit, not that it failed.

How 80 Plus works

The 80 Plus program is run by CLEAResult. Its official rating chart lists the minimum efficiency a supply must reach at each load point, for each input voltage. As listed on the chart in October 2026, the tiers are Standard, Bronze, Silver, Gold, Platinum, Titanium and Ruby, with Ruby the newest and strictest.

For a 115 V non-redundant desktop supply, the chart requires:

  • Standard: 80% at 20%, 50% and 100% load.
  • Bronze: 82% / 85% / 82% at 20% / 50% / 100% load.
  • Silver: 85% / 88% / 85%.
  • Gold: 87% / 90% / 87%.
  • Platinum: 90% / 92% / 89%.
  • Titanium: 90% at 10% load, then 92% / 94% / 90%.

For 230 V EU supplies the bars are higher. Gold needs 90% / 92% / 89% and Titanium needs 90% / 93% / 95% / 91% across 10%, 20%, 50% and 100% load. A unit can carry a Gold label tested at 230 V and still fall short of the 115 V Gold chart numbers, which is why the voltage on the certificate matters.

The program also sets power factor conditions, and the exact thresholds differ by tier and load. The 80 Plus program page links to the testing protocol for details.

How Cybenetics ETA works

Cybenetics, an independent lab, describes its method on its methodology page. It loads the +12 V, 5 V and 3.3 V rails with automated loaders across more than 1,450 combinations, then interpolates up to about 25,000 readings. The ETA grade is based on overall average efficiency across that range, not on three or four points.

The test also differs from 80 Plus in conditions. Cybenetics runs the unit in a hot box set to 30 °C, with ambient readings of up to about 32 °C, to approximate the inside of a PC case. It supports both 115 V at 60 Hz and 230 V at 50 Hz.

As of October 2026, the ETA criteria for 115 V input are:

  • Diamond: overall efficiency of 93% or more.
  • Titanium: 91% to under 93%.
  • Platinum: 89% to under 91%.
  • Gold: 87% to under 89%.
  • Silver: 85% to under 87%.
  • Bronze: 82% to under 85%.

At 230 V the thresholds move up by two points: Diamond starts at 95%, Titanium at 93%, Platinum at 91%, Gold at 89%, Silver at 87% and Bronze at 84%. Each tier also carries power factor, 5VSB standby efficiency and vampire power limits. For example, 115 V Gold requires a power factor of at least 0.970 and standby draw under 0.19 W.

Why the same unit gets different grades

The two schemes ask different questions. 80 Plus asks whether the supply clears a threshold at specific load points. ETA asks what the average is over everything the unit can do. A supply tuned to hit the 80 Plus marks at 20%, 50% and 100% can still sag in between or at very light load, and ETA will show it.

Other differences add up:

  • Temperature: warmer test conditions lower efficiency slightly.
  • Voltage: a rating earned at 230 V does not transfer to 115 V.
  • Sample: each lab tests the sample it receives, and units vary.

In practice, many supplies carry an 80 Plus tier and a different Cybenetics tier on the same box. Neither is wrong. They are different measurements.

Cybenetics LAMBDA: the noise rating

80 Plus has no noise component. Cybenetics fills that gap with LAMBDA. Fan noise is measured in a controlled acoustic chamber under the same warm conditions as the efficiency test. The classes are:

  • A++: below 15 dB(A)
  • A+: 15 to under 20 dB(A)
  • A: 20 to under 25 dB(A)
  • A-: 25 to under 30 dB(A)
  • Standard++: 30 to under 35 dB(A)
  • Standard+: 35 to under 40 dB(A)
  • Standard: 40 to under 45 dB(A)

If a result lands within 0.25 dB(A) of a class limit, the manufacturer may submit a second sample, and a third is requested if the two differ by more than 2 dB(A).

Why a Gold label can mislead

A supply labeled Gold has met the Gold chart at the tested points, nothing more. Check these before trusting it:

  1. Which voltage was certified. A 230 V Gold rating is a different bar from 115 V Gold.
  2. Which scheme issued the label. Some marketing copy says "Gold" without naming 80 Plus or Cybenetics. Search the vendor's model in the certification databases.
  3. Whether the rated model matches the one you buy. Certificates cover specific models and wattages, and a manufacturer can use the same platform for several.
  4. Noise and load behavior. A Gold supply with a loud fan at typical load can be a worse buy than a Silver one that stays quiet.

What to check in a review instead

Look for measured efficiency curves rather than a tier name, a LAMBDA class or noise measurements at realistic load, and ripple and hold-up results. Also confirm connector support, especially if you are pairing the supply with a modern graphics card. Our guide to the 12V-2x6 connector covers that side.

Efficiency also matters less than it sounds for most desktops. A few percentage points at typical loads change the electricity bill modestly, so noise, build quality and warranty often decide the purchase. For more hardware coverage see our Industry and Chips sections, and Launches for new product releases.

Frequently asked questions

Is 80 Plus Gold the same as Cybenetics Gold?

No. 80 Plus Gold is a pass mark at set load points, while Cybenetics Gold is an average over the full operating range under warmer conditions. A single supply can earn different tiers from each.

Is Cybenetics better than 80 Plus?

Cybenetics measures more of the load range and adds a noise rating, so it gives a fuller picture. 80 Plus remains the more widely printed label and is a sound minimum check.

What is Cybenetics LAMBDA?

LAMBDA is Cybenetics' noise certification for power supplies. It grades fan noise from Standard (40 to under 45 dB(A)) up to A++ (below 15 dB(A)).

Is 80 Plus Titanium worth paying for?

Titanium adds a 10% load requirement and higher bars than Platinum at the 20% and 50% points, which suits supplies that often idle at low load. For a typical home PC the electricity savings over Gold are usually small, so price and noise should weigh in too.

Does a PSU need to be certified to be good?

No. Certification is voluntary, so a good supply may be uncertified. Without a label, rely on independent measurements.